Roughing Cut 4.5 Overall Length Weldon Shank 1.25 Cutting Diameter Finish Non-Center Cutting 6 Flutes 1.25 Shank Diameter Uncoated Bright 30 Deg Helix YG-1 E2079 Cobalt Steel Square Nose End Mill

YG-1 E2079 Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated (Bright) Finish, Roughing Cut, Non-Center Cutting, 30 Deg Helix, 6 Flutes, 4.5' Overall Length, 1.25' Cutting Diameter, 1.25' Shank Diameter: Home Improvement. YG-1 E2079 Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated (Bright) Finish, Roughing Cut, Non-Center Cutting, 30 Deg Helix, 6 Flutes, 4.5" Overall Length, 1.25" Cutting Diameter, 1.25" Shank Diameter: Home Improvement. The E079 uncoated cobalt steel roughing square nose end mill has a fine pitch, multiple flutes, a non-center-cutting design, and a 30-degree helix angle for peripheral roughing on a range of materials. The end mill has chip-breaking cutting edges that create small chips for heavy cuts and remove material in less time than conventional end mills, with minimal vibration (chatter). It produces a rough finish that can be smoothed by a second finishing cut. The number of flutes varies by diameter to optimize the feed and cut rate. The non-center-cutting design is for applications such as peripheral milling. The tool’s square end creates sharp, unrounded cuts. The 30-degree helix angle supports general-purpose applications. It balances lower angles’ strong cutting edge for difficult-to-machine materials with higher angles’ increased cutting action. 。 Cobalt steel can be run at faster speeds and stays sharp longer than high-speed steel tools, while offering resistance to heat and abrasion. With no coating or surface treatment, this uncoated tool can be used on a range of materials. Cutting diameter tolerance is + 0.0030 to - 0.0000" for cutting diameters up to " and + 0.0060 to - 0.0000" for cutting diameters over ". This tool has a Weldon shank. 。 End mills are designed to remove material and create multi-dimensional shapes and profiles. They have cutting edges along the outside diameter and flutes that remove chips from the cutting area and allow cooling fluids to enter. If heat is not reduced effectively, the tool’s cutting edges will dull and additional material buildup can occur. The number of flutes can range from two to eight. Two-flute designs offer the most efficient chip removal, but more flutes provide a smoother finish. The shank is the end of the tool held in place by a tool holder or machine. Center-cutting end mills can create three-dimensional shapes and profiles, and make plunge cuts similar to a drill bit. Non-center-cutting end mills are for applications such as peripheral milling and finishing, but cannot make plunge cuts. 。 manufactures drills, taps, end mills, and rotary tooling. The company, founded in 98, is headquartered in South Korea and has a U.S. office in Vernon Hills, IL. 。 。 。 。 。

Roughing Cut 4.5 Overall Length Weldon Shank 1.25 Cutting Diameter Finish Non-Center Cutting 6 Flutes 1.25 Shank Diameter Uncoated Bright 30 Deg Helix YG-1 E2079 Cobalt Steel Square Nose End Mill
Roughing Cut 4.5 Overall Length Weldon Shank 1.25 Cutting Diameter Finish Non-Center Cutting 6 Flutes 1.25 Shank Diameter Uncoated Bright 30 Deg Helix YG-1 E2079 Cobalt Steel Square Nose End Mill
Roughing Cut 4.5 Overall Length Weldon Shank 1.25 Cutting Diameter Finish Non-Center Cutting 6 Flutes 1.25 Shank Diameter Uncoated Bright 30 Deg Helix YG-1 E2079 Cobalt Steel Square Nose End Mill
Roughing Cut 4.5 Overall Length Weldon Shank 1.25 Cutting Diameter Finish Non-Center Cutting 6 Flutes 1.25 Shank Diameter Uncoated Bright 30 Deg Helix YG-1 E2079 Cobalt Steel Square Nose End Mill
Roughing Cut 4.5 Overall Length Weldon Shank 1.25 Cutting Diameter Finish Non-Center Cutting 6 Flutes 1.25 Shank Diameter Uncoated Bright 30 Deg Helix YG-1 E2079 Cobalt Steel Square Nose End Mill
Roughing Cut 4.5 Overall Length Weldon Shank 1.25 Cutting Diameter Finish Non-Center Cutting 6 Flutes 1.25 Shank Diameter Uncoated Bright 30 Deg Helix YG-1 E2079 Cobalt Steel Square Nose End Mill
Roughing Cut 4.5 Overall Length Weldon Shank 1.25 Cutting Diameter Finish Non-Center Cutting 6 Flutes 1.25 Shank Diameter Uncoated Bright 30 Deg Helix YG-1 E2079 Cobalt Steel Square Nose End Mill
Roughing Cut 4.5 Overall Length Weldon Shank 1.25 Cutting Diameter Finish Non-Center Cutting 6 Flutes 1.25 Shank Diameter Uncoated Bright 30 Deg Helix YG-1 E2079 Cobalt Steel Square Nose End Mill